We do indeed offer ramp door extenders in a variety of sizes. For example the Race Ramps Trailer Loading Assist Ramps # RR-TR-5 are a very popular size. These are 67" long ramps and have a 5" lift. They can be used to load a vehicle weighing up to 6,000 lbs onto a trailer. The ramps themselves are made from a high density EPS foam and weigh only 10 lbs apiece. We do offer a variety of sizes from the 54" long # RR-TR-6 all the way up to the 136" long # RR-TR-11-2. view full answer...
We do! There are a variety of trailer ramp styles and needs out there so we have quite a selection to choose from.
For example, we have the 60" x 14-1/2" Aluminum Car Hauler Ramp Set # 288-07502 rated for 6,000 lbs, the 84" x 14" Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R84 rated for 6,000 lbs, or the 90" x 18" Arched Loading Ramp Set # 288-07432-2 rated for 3,000 lbs.
I'm attaching our selection of ramps for you to filter through, but if you could let me know how you're planning... view full answer...
Currently we only offer the Race Ramps Trailer Loading Assist Ramps # RR-TR-8 as a pair as that is the only way Race Ramps offers them. We do not have the ability to sell them individually. view full answer...
It sounds like you have a utility/equipment trailer with two 8' ramps. The only springs that we have that will work for that style are the Ramp Spring - 2K Torque for 1-1/2" Shaft # RS16933RH (for Right Hand) and # RS16933LH (for Left Hand). These springs will work with shafts that are 1-1/2" and they have 2,000 lbs. of torque.
I have included a video that reviews these springs and shows an installation for you to check out. view full answer...
Sounds like you have a rear ramp/door on a horse trailer and need a cam style latch to hold it in place when shut. For that the 36" Lock Side-Door Bar Lock Assembly # 305736 can be used for this. It would be just a matter of mounting the assembly on top of the ramp/door to hold it up there. Or you could use two of these, one on each side and that would work as well. There are holes on the latches that you can run a padlock through like the # ML1KA.
If you have something totally different... view full answer...
The only ramp door type hinge we have that is weld on with a removable pin is the Aluminum # PLR1005. While the Ramp Door Hinge # PLR1902 you found does not have a removable pin you could weld it to a removable plate on the trailer which would then allow you to remove the entire ramp along with the hinges. view full answer...
Without knowing the dimensions and weight of your ramp it is hard to make a specific product recommendation but we do offer all sorts of trailer hardware. You might do well with an inexpensive hook and keeper like # 383400 or # PLR9-SS, or a spring latch like # SL716.
I recommend using one latch on each side of the ramp. view full answer...
I have included a link below to the Folding Steel Ramp for Pro Series Solo Cargo Carrier, # PS1040200. Current pricing and information can be found on the product page. As you have stated, the ramp is designed to fit Pro Series Solo hitch-mounted cargo carrier # PS1040100.
You can also order the cargo carrier with the ramp already attached. Take a look at the 32x48 Pro Series Steel Solo Cargo Carrier and Folding Ramp, # PS10401-10402.
The cargo carrier will fit your 2006 Dodge Grand Caravan... view full answer...
I believe you are looking for the Blaylock EZ Jack part # EZ-JACK. This is a ramp that you can roll up on that will allow you to change a tandem axle trailer spare. view full answer...
There is an aluminum trailer hitch mount cargo carrier that can fold up, the Curt 19 X 60 # C18100, but it does not have a ramp.
Then there is an aluminum carrier with a ramp that doesn't fold up, the Flint Hill Goods 30 X 50 # FHG69ZR.
Then we have a steel carrier that folds and has a ramp, the Flint Hill Goods # FHG77ZR.
I attached video reviews of these products for you. view full answer...
While there is no ramp option for the Carpod, # M2200, we do have trailer hitch mount cargo carriers that do have ramps. I have included a link to them for you to view.
What you could then do, to keep your items secure and deter theft is to use a cable lock, like # HRLHPC2, which also serves as a hitch lock to lock the carrier to the hitch. I have included a link to a video review of the Cable lock for you to view. view full answer...
Yes! We do carry the the Hollywood Racks RV Rider # HLY64FR (HR1700).
If you are looking for a great alternative with a ramp, I recommend the Yakima OnRamp Bike Rack for 2 Electric Bikes - 2" Hitches # Y36FR. The OnRamp is great because it is approved not only for standard vehicles, it is also approved for fifth wheel trailers, motorhomes, travel trailers, and flat-towed vehicles. It is important to note that the OnRamp does have a decreaed 40-pound per-bike weight capacity when mounted... view full answer...
For a cargo carrier with a ramp that has a shank rise of 4 inches, I recommend the Pro Series Steel Solo Cargo Carrier and Folding Ramp # PS10401-10402. However, this ramp has a weight capacity of 400 pounds.
This carrier is designed to fit in 2 inch trailer hitch receivers. The carrier alone weights 105 pounds. I have attached a review video of this carrier for you. view full answer...
The Yakima OnRamp Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount # Y36FR is the correct model you're looking for, that will fit on a 2" hitch. The OnRamp can be used on vehicles, trailers, RVs or flat towed vehicles, so they're a great solution for whatever you need to use it with.
I've linked a review of this video of this bike rack for you to check out. view full answer...
We have several hinge pins like # HP412G that I have linked for you, but it sounds like you need actual springs. We have some heavy duty ramp springs like # RS16933RH and # RS16933LH if you happen to have a heavy duty equipment trailer like what they haul tractors and other large equipment on.
For an open utility trailer you may be able to use a tailgate assist like # RA-27C. Or for an enclosed trailer we have springs that are similar to garage door systems. I have linked those as well.... view full answer...
While we do have the option of using the Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes # HLY84FR with trike adapter # HRTRK-ADP. This will only accommodate the trike. It will not allow for a second bicycle to be loaded and it does not have a load ramp option.
The best option we will have that meets your needs of carrying an Electric Trike, an adult size cruiser style bike and have loading ramp option will be the Detail K2 Mighty Multi Utility Trailer at 6' Long, # K2MMT4X6. view full answer...
The M-3 Enclosed Trailer Ramp Spring that you referenced, part # CB250D96SHD, has a 250-lb capacity and this is the highest-rated of all such available items.
If you decide to replace your ailing winch with a new one I suggest a brake winch or a worm gear winch since both of these types will prevent the ramp from free-falling. For a worm gear winch you might use the 1500-lb rated Dutton-Lainson # DL10950 that can be used with winch cable # DL24100.
Two links at right will take you to... view full answer...
I have attached a link to this answer page for you that will show you all of our hitch-mounted carriers with a ramp. These racks would allow you to carry an electric mobility chair at the Curt Class III Trailer Hitch Receiver # C13172 your 2015 Jeep Cherokee.
There are a number of different style options for you to choose from when it comes to a cargo carrier with a ramp. Most carriers are made of steel, like # PS10401-10402, but some carriers are made from aluminum to keep the weight... view full answer...
We do offer two versions of trailer ramp screen products. Part # 052963799842 is intended for fiberglass or aluminum toy haulers, while part # 052963799941 is for steel trailers. Both of these screens offer adjustability to get the right fit on any given trailer. We offer no custom-fit screen products since there are so many variations in trailer design. view full answer...
We unfortunately do not carry additional lengths of the cables included with the Conventional Ramp Door Spring for 7' Wide Enclosed Trailer # M374FR, but you could definitely find some at your local hardware store. view full answer...
Go To Results